FOR ONE PHASE PUMP MOTORS

Sirio Entry and Sirio Entry XP are pump controls with inverter technology. That means, they control the speed rive of the pump with adjusting the frequency. With the help of the inverters, we can hold the pressure constant in the system.

Moreover Sirio Entry and Sirio Entry XP protect the pump from dry running, over current, water hammers, breakaway from starting current. Contains a digital display for the necessary infromations (current, pressure, etc…) and the buttons help in the settings of the parameters.

Sirio Entry and Sirio Entry XP must be install on the pipe, according to the water flow in any position. When the pump stop due to a malfunction, Sirio Entry and Sirio Entry XP will restart automatic, according to the pre set values of the restart. A perfect solution to automatize the hidrofor system, and protect the pump.

Power mains supply:	230 V~ ±10% 50/60Hz single phase
Motor power output:	220 V~ single phase
Max. motor power:	Sirio Entry :1500 W / Sirio Entry XP: 1800 W
Max. line absorption:	Sirio Entry: 12A @ 230 V~ / Sirio Entry XP: 16A @ 230 V~
Max allowed pressure	8 bar
Max fluid temperature:	50 °C
Pressure drop:	0,1 bar at 150 l/min
Set point adjustement range:	1,5 – 7 bar
Start pressure adjustment range:	1 – 6,7 bar
Hydraulic connection:	1″ ¼ male
Frequency modulation range:	25 – 50 Hz
Protection degree:	IP X5

 

FOR THREE PHASE PUMP MOTORS

Sirio is a VFD (Variable Frequency Driver) for pumps. Sirio was made to control the pump’s speed and hold the pressure to a constant value within the hidrofor system. Not only controls the pump, but protect it from:

• Dry running
• Over current

It has a display to show the values of the pump (current absorption, pressure, frequency etc…) and can be set with the buttons on the interface. Sirio must be installed on the pipe system in any position, but according to the flow direction.

If the pump stops by an error, Sirio will display the source of the error, and restart the pump according to the restart parameters.

Power mains supply:	230 V~ ±10% 50/60Hz single phase
Motor power output:	220 V~ three phase
Max. motor power:	2200 W
Max. line absorption:	16A @ 230 V~
Max allowed pressure	8 bar
Max fluid temperature:	50 °C
Pressure drop:	0,1 bar at 150 l/min
Set point adjustement range:	1,5 – 7 bar
Start pressure adjustment range:	1 – 6,7 bar
Hydraulic connection:	1″ ¼ male
Frequency modulation range:	25 – 50 Hz
Protection degree:	IP X5

ONE PHASE POWER SUPPLY
ONE PHASE PUMP MOTOR

Hydrocontroller is a Variable Frequency Driver pump control. The device can be installed on wall (air cooled), or in the pipe system (water cooled) according to the water flow.

The user-friendly interface helps the easy installation and calibration of the Hydrocontroller.

Hydrocontroller variable the speed of the pump motor, setting the pressure constant in the system, and protect the pump from any malfunction (see below the data sheet).

Hydrocontroller can manage one (ST) and multi pump system (ADV).

WARNING!

The connection cable creates, between HydroController and pump, a capacitive effect. For removing the disturbance we need an adapter for long connection L>10 m (33 feet), up to 80 m (260 feet) of cable. This device is normally used with submersible pumps in well applications.

Hydrocontroller have domestic use EMC approval. If inverter is installed in enviroments particularly sensitive to electromagnetic interference, additional EMI filters must be installed between the supply and inverter, so as to eliminate.

ONE PHASE POWER SUPPLY
THREE PHASE PUMP MOTOR

Hydrocontroller is a Variable Frequency Driver pump control. The device can be installed on wall (air cooled), or in the pipe system (water cooled) according to the water flow.

The user-friendly interface helps the easy installation and calibration of the Hydrocontroller.

Hydrocontroller variable the speed of the pump motor, setting the pressure constant in the system, and protect the pump from any malfunction (see below the data sheet).

Hydrocontroller can manage one (ST) and multi pump system (ADV).

WARNING!

The connection cable creates, between HydroController and pump, a capacitive effect. For removing the disturbance we need an adapter for long connection L>10 m (33 feet), up to 80 m (260 feet) of cable. This device is normally used with submersible pumps in well applications.

Hydrocontroller have domestic use EMC approval. If inverter is installed in enviroments particularly sensitive to electromagnetic interference, additional EMI filters must be installed between the supply and inverter, so as to eliminate.

THREE PHASE POWER SUPPLY
THREE PHASE PUMP MOTOR

Hydrocontroller is a Variable Frequency Driver pump control. The device can be installed on wall (air cooled), or in the pipe system (water cooled) according to the water flow.

The user-friendly interface helps the easy installation and calibration of the Hydrocontroller.

Hydrocontroller variable the speed of the pump motor, setting the pressure constant in the system, and protect the pump from any malfunction (see below the data sheet).

Hydrocontroller can manage one (ST) and multi pump system (ADV).

WARNING!

The connection cable creates, between HydroController and pump, a capacitive effect. For removing the disturbance we need an adapter for long connection L>10 m (33 feet), up to 80 m (260 feet) of cable. This device is normally used with submersible pumps in well applications.

Hydrocontroller have domestic use EMC approval. If inverter is installed in enviroments particularly sensitive to electromagnetic interference, additional EMI filters must be installed between the supply and inverter, so as to eliminate.

 

---

 

Reducing energy consumption in the world is everyone’s responsibility in order
to reduce waste. In this scenario we committed to do the best we can by
developing products, for boosting systems, that enable low energy consumption.

---

Similar to the Hydrocontroller, E-Power is a VFD for residental usage. Controls the pump’s start and stop functions, and protect the pump (see below in the data sheet).

E-Power must be installed on the pipe in any position, but according to the flow direction. The water cool the internal construction and the sensors sense the flow whitout loss.

The device consist an external output for a float switch or remote control, and an output relay, what can be used as a warning signal.

E-Power is a patented product!